Sean Kilcarr, Senior Editor

January 1, 2008

7 Min Read
Up and Running

In a time of more expensive refuse trucks, it's crucial that haulers get the most out of the new vehicles they buy. Fleet experts say the foundation for maximizing a truck's lifespan and its uptime are proper spec'ing of components and thorough preventive maintenance (PM).

Because of budget concerns, cutting costs may be tempting when it comes to spec'ing and PM; however, experts say haulers should resist that temptation. “Too often, price drives the spec decision, [but] additional dollars up front can have an extremely positive impact over the life of the vehicle,” says Trevor Bridges, vice president of service and warranty for Hagerstown, Ind.-based Autocar. “Another key point to get across is that preventive maintenance cannot take a back seat to anything. The technician shortage and budgetary constraints occasionally dictate how well or how poorly PM is done in the transportation industry. But doing it — and doing it on a regular schedule — is the key.”

Starting with Specs

Properly spec'ing a refuse truck is the first step toward getting peak performance from your fleet. “If any component on the vehicle is under spec'd, frequent breakdowns and high maintenance are almost assured,” says Dennis Manchester, manager of vocational sales for Portland, Ore.-based Daimler Truck North America, formerly Freightliner Trucks. “The life expectancy of the component will be significantly reduced and shorter overhaul cycles will result. Prime examples of this are driveline components, axles, suspensions and frames. Equipment that is not properly spec'd for a particular job may require more time to complete a route or travel to a landfill or transfer station, thereby requiring additional equipment to service a set number of customers and driving up total operating costs.”

Darry Stuart, president of Boston-based DWS Fleet Management Services, a firm specializing in fleet management issues, says the smart refuse fleet manager should spec a truck that can last 12 or 13 years, if needed. This gives a hauler the option of selling the vehicle after eight or 10 years if the market is good, or holding on to it for a few more if it is not.

“You need to remember that what you are buying is uptime — the less time the truck is in the shop, the better,” says Stuart, who spent five years of his 35-year career as a fleet manager for BFI, prior to its 1999 purchase by Allied Waste Industries. “The way to be competitive today is by managing your vehicle downtime and uptime better than the next guy.”

Haulers should spec suspensions and axles with a higher load rating than what they intend to haul and consider equipping the vehicle with bigger frames, tires and engines than their day-to-day operations demand, says Brian Lindgren, director of vocational sales for Seattle-based Kenworth Truck Co.

Common spec'ing mistakes include wheelbase and body-related issues, such as misjudging the amount of clear back-of-cab space, which is critical on all applications, says Jim Zito, director of sales-vocational markets for Denton, Texas-based Peterbilt Motors Co. For example, an automated side loader requires the right side of the chassis to be free of fuel tanks and battery boxes so that the arm can operate. Failure to take this into account in the specs means the tank and box will have to be moved by the body company, costing the customer a great deal of money. Making sure fleets spec market-specific components on their waste trucks also is critical, especially in terms of maintaining refuse vehicle productivity.

Focusing on Fluids

Once the truck specs are in place, fleets need to turn their attention to the fluids coursing through both the vehicle and the body: engine oil and coolant, transmission fluid, hydraulic fluids and wheel bearing grease.

Joel Barnes, technical training manager for Chattanooga, Tenn.-based Heil Environmental, says the refuse body maker has performed studies over the last three years, examining the performance of different grades of greases and lubricants in the refuse market. “We found one fleet rebuilt their automated truck's lift arm three times versus zero [times] for another fleet over that same three-year span, simply due to the better grade of lubricant used [by the former fleet],” he says.

Melissa Gauger, waste segment manager for Warrenville, Ill.-based International Truck & Engine Corp., recommends using synthetic fluids, such as engine oil and hydraulic fluids, everywhere possible because they handle extreme cold and heat better than conventional fluids, and sometimes allow for longer maintenance intervals.

Synthetic fluids have an enormous effect on maintenance costs, Autocar's Bridges says. “For example, synthetics in automatic transmissions have dramatically extended [fluid] change intervals,” he says. “Again, this increases the upfront cost, but, in my opinion, synthetics have had a dramatic effect on lowering the overall maintenance cost.”

“There is also a bonus in reduced environmental impact, as we're throwing away less oils, etc., because we are using them longer,” he says.

Fleets should synchronize the PM of a vehicle's various components so that they are servicing the engine, chassis and body at the same time, which reduces maintenance costs, experts say. “It doesn't help to use an extended 600-hour engine coolant if you have to change the hydraulic fluid at 300 hours,” Gauger says.

Barnes stresses that refuse fleets must look at the vehicle as a single unit — truck chassis and packer together — to maintain peak performance. “Many fleets are focused on keeping the engine oil clean, but forget about the needs of the hydraulic fluid,” he says.

Maintenance Practices

Once a truck is up and running, fleets must pay careful attention to PM. Not performing maintenance, or trying to stretch maintenance intervals without the approval of the component and vehicle manufacturers, invariably results in breakdowns, unscheduled repairs and overall higher operating costs. “Routine service and maintenance allows the technician to recognize any issues at that time, rather than the vehicle breaking down on the job and being pulled from service,” Peterbilt's Zito says, adding that breakdown maintenance ultimately costs more in the long run.

DWS's Stuart stresses to fleets that, while they should not downplay the value and importance of the role electronics play in controlling all the features on today's refuse truck, the highest maintenance cost they'll experience is not in those areas. Instead, it's tires, brakes, hydraulics, grease, slack adjusters and other basic equipment. “The most basic components of the truck relate to your highest maintenance costs [and] highest out of service rates,” he says. “All the twisting and turning, plus stopping and starting, wears them out. Refuse is still very much a basic business.”

Keeping detailed records is a critical part of a PM program. Fleets should maintain records by chassis type and unit number so that they can easily compare truck and component brands and specs to determine what works for their particular applications, Lindgren says.

Data entry should be as simple as possible to make sure that the maintenance database is kept up-to-date and accurate. “If the data points are not entered correctly, it is all but impossible to work on a predictive maintenance strategy,” Bridges says.

Fleets also should educate their drivers on ways that they can reduce the stress placed on vehicles while they are out on their routes. For example, most automated truck drivers run the packer after every time they dump a can; however, running the packer only after every third dump would significantly reduce the wear and tear on the vehicle, reducing maintenance costs, says Heil's Barnes.

Finally, there's the tricky issue of spare parts. Many fleets are worried about tying up dollars in inventory that just sits on a shelf, but DWS's Stuart says refuse fleets need to keep at least critical hard-to-find parts close at hand. “Sure, there's a fear of spending money on parts, but waiting on a part puts a truck down, meaning it's not generating revenue,” he says.

Stuart says fleets not only should keep critical items on hand, but should ensure that they can find them quickly. “It's no good tracking your parts inventory via computer if your techs can't find it in the stockroom,” he says. ”

Final Analysis

“Refuse customers are in a tough, competitive business that demands maximum efficiency,” says Steve Ginter, vocational product manager for Allentown, Pa.-based Mack Trucks. To achieve that efficiency and operate trucks on the road for as long as possible, fleets must make proper spec'ing and sufficient preventive maintenance top priorities. To do so costs money, but not doing so courts bigger financial headaches such as expensive repairs and vehicle downtime.

Sean Kilcarr is senior editor of Fleet Owner, a sister publication of Waste Age.

About the Author(s)

Sean Kilcarr

Senior Editor, Fleet Owner

Sean Kilcarr is the senior editor of Fleet Owner.

Stay in the Know - Subscribe to Our Newsletters
Join a network of more than 90,000 waste and recycling industry professionals. Get the latest news and insights straight to your inbox. Free.

You May Also Like